UG齿轮设计-直齿锥齿轮

四五设计网小助手 ug评论阅读模式

(6)采用以前的方法做出第一个齿廓。

即大段齿廓。注意,因为坐标是旋转以后的,文章源自四五设计网-https://www.45te.com/2391.html

所以镜像渐开线时不需再作镜像中心线,直接用基准坐标系的YZ平面即可。文章源自四五设计网-https://www.45te.com/2391.html

(7)参照第一个齿廓的做法,做出第二个齿廓。文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html

偏置坐标系时的对话框                  画第二条渐开线时记得修改X、Y的参数文章源自四五设计网-https://www.45te.com/2391.html

(8)结果如下:文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html

(9)画引导线。文章源自四五设计网-https://www.45te.com/2391.html

①首先要使坐标系恢复WCS原点。选择参考为:绝对坐标系即可。如图:文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html

②以YZ为草图平面,画出引导线时,最好选择第二条直线的投影。文章源自四五设计网-https://www.45te.com/2391.html

即这条直线为引导线文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html

(10)再以YZ为草图平面画出齿坯剖面,并旋转成实体。文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html

(11)扫掠出第一个齿体。文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html

(12)阵列并求和。(NX 8.0阵列命令用的是“对特征形成图样”)文章源自四五设计网-https://www.45te.com/2391.html

UG齿轮设计-直齿锥齿轮文章源自四五设计网-https://www.45te.com/2391.html 文章源自四五设计网-https://www.45te.com/2391.html

  • 我的微信
  • 微信扫一扫
  • weinxin
  • 惠生活福利社
  • 微信扫一扫
  • weinxin
四五设计网小助手
  • 本文由 发表于 2022年3月17日 11:11:49
  • 转载请务必保留本文链接:https://www.45te.com/2391.html
评论  0  访客  0

发表评论

匿名网友 填写信息

:?: :razz: :sad: :evil: :!: :smile: :oops: :grin: :eek: :shock: :???: :cool: :lol: :mad: :twisted: :roll: :wink: :idea: :arrow: :neutral: :cry: :mrgreen: